ISO8859-1>0!3RbG  +'M@K& 5 sY %Y   q Ilzf8(   , < ] va! .Disk Maintenance Disk to disk copy, display/alter sectors.DISK MAINTENANCE SERVICE AID DISK MAINTENANCE SERVICE AID Disk to Disk CopyDISK MAINTENANCE SERVICE AID Display/Alter SectorDisk to Disk Copy Copies the entire contents of one disk (including the volume ID) to another disk. Assumes the target disk is formatted. All data on the target disk is lost.Display/Alter Sector Allows selected sectors of a selected disk to be displayed and altered.Do not CopyCopyContinue CopyingAbort Copy ProcessDisregard WarningTerminateMove cursor to selection, then press Enter.Press Enter to continue.Move the cursor to the disk you want to copy from (source), then press Enter.Move the cursor to the disk you want to copy to (target), then press Enter.A valid LVM record exists on the target disk (%s), indicating that the disk is in an LVM Volume Group. If you believe the target disk is NOT a member of an LVM Volume Group (for example, the disk was taken from another system and never added to a Volume Group on this system), you may disregard this warning. If you believe the disk IS a member of an LVM Volume Group, you should terminate this procedure and select a different target or delete the disk from its Volume Group before proceeding. Move cursor to selection and then press Enter.Source disk (%s) will be copied to target disk (%s). The size of the source disk is %d sectors. The size of the target disk is %d sectors. (If the target is larger than the source, the additional space may be inaccessible after the copy is complete.) * * * WARNING! * * * THE COPY OPERATION WILL DESTROY ALL OLD DATA ON THE TARGET DISK. Move cursor to selection and then press Enter.%s at location %sCopying %s to %s. %d%% complete. Please stand by.An unrecoverable read error has occurred on the source disk at sector %s. This procedure is terminating. You may need to run diagnostics on the source disk (%s).The maximum number of write errors allowed on the target disk (%s) has been exceeded. This procedure is terminating. You may need to run diagnostics and/or replace the disk.Unable to open target disk (%s), possibly due to conflict with another user or program.Unable to open source disk (%s), possibly due to conflict with another user or program.Less than two disk drives were found in the Customized Device Database, or less than two disks could be opened to read their capacities. At least two disk drives must be available to perform the Disk to Disk Copy operation.Unable to open source disk (%s), due to conflict with another user or program. One solution is to run diagnostics from removeable media (that is, in standalone mode). If you want to perform the copy while in concurrent mode, you will need to prevent other access to the disk by unmounting any filesystems on the disk or, if the disk is in an LVM Volume Group, remove the disk from the Volume Group or vary the Volume Group off.Unable to open source disk (%s), due to possible hardware error. You may need to run diagnostics on the disk and SCSI adapter.Unable to copy the source disk (%s), because a read error occurred while reading the LVM record or the Bad Block Directory, or the Bad Block Directory is corrupt.This system configuration does have any disks supported by this command. The source disk (%s) has been copied to the target disk (%s). The system cannot operate normally with both drives. You may return to the original configuration by removing and undefining the target disk, or complete the replacement of the source disk by physically removing both disks, setting the SCSI ID of the target disk to the that of the source disk, and physically installing the target disk at the source disk's original location. There are no other disks to copy to that are the same size as the source disk (%s). Procedure terminating.There are no other disks to copy to that are not smaller than and not more than 10%% larger than the source disk (%s). Procedure terminating.*** WARNING *** Inappropriate modifications to some disk sectors may result in total loss of all data on the disk drive.Enter the sector number (in decimal) that you would like to display/alter on the selected disk (%s):Sector number (0-%d):Sector %d on %s.Use tab key to switch between hex and ASCII, F7 to save.Offset:F1=Help F3=Cancel F7=Commit F10=ExitHex WindowASCII WindowAre you sure you want to save the changes to sector %d? Press Enter to save changes and return to the edit panel, Cancel to return to the edit panel without saving changes.No disk drives were found in the Customized Device Database.Unable to open the selected disk (%s), possibly due to conflict with another user or program.Sector %s is unreadable.Unable to write sector %s.Enter the sector number (in decimal) that you would like to display/alter on the selected disk.No LIST data for this function!!!This procedure is intended to support the replacement of an existing disk drive with a new disk drive. The new disk drive must be the same size or no more than 10%% larger than the existing disk drive. If you have not already done so, install the new disk drive by setting its SCSI address to an address that is not currently in use and installing it in an empty location. Both the old (source) and new (target) disk drives must be installed and available for use in order to perform the Disk to Disk Copy operation. Once the copy is complete, only one of the disks may remain installed. Either remove the target disk to return to the original configuration OR perform the following procedure to complete the replacement of the old (source) disk with the new (target) disk: 1. Remove both disks. 2. Set the SCSI address of the new (target) disk to the SCSI address of the old (source) disk. 3. Install the new disk in the old disk's location.