ISO8859-1$Oh5O  $5o&Ta{k I   '-['o X g u = 6 + t QJE6 |(fDISPLAY MICROCODE LEVEL %1$s %2$sINSTALL MICROCODE %1$s %2$sYesNoPlease run diagnostics on the device to ensure that it is functioning properly.An error was detected while unconfiguring the device. Unable to return the device to its original state.Run diagnostics on the device to isolate the problem.Run diagnostics on the adapter connected to this device to isolate the problem./etc/microcodedisketteThe source of the microcode image can either be on the disk in /etc/microcode or on a diskette. Select the source of the microcode image.Insert the microcode diskette in diskette drive %1$s.There is no diskette drive on the system. Please use /etc/microcode as the source for the microcode image file.Microcode installation is in progress.Installation of the microcode has completed successfully. The current microcode for %1$s is %2$s.Installation of the microcode has not completed successfully. The current microcode for %1$s is still %2$s.The current microcode for %1$s is %2$s. Available levels to install are listed below. Select the microcode level to be installed. Use Help for explanations of "M", "L", "C" and "P" .%1$c %2$sThis node does not have exclusive disk access to download microcode. Please try to download microcode on the node where the disk is located.The current microcode for %1$s is %2$s.An error was detected while configuring %1$s.The microcode image currently installed on the device could not be found on the selected source. Use Enter to continue the installation. Use Cancel to cancel the installation.The device is already at the selected microcode level. Use Enter to continue the installation. Use Cancel to cancel the installation.There was a problem accessing %1$s. Please make sure there is a microcode diskette in %2$s.Could not restore the image from %1$s. Please make sure there is a microcode diskette in backup format in %2$s.No valid microcode image was found in %1$s. Microcode image files for this device have the naming convention %2$s.XXXXXXXX where XXXXXXXX is the revision level of the microcode.There was a problem with the microcode image file. Please make sure that the file is a valid microcode image and is not corrupted. Contact the service support structure for further assistance.A software error occurred. Contact the service support structure for further assistance.Microcode installation is not supported for this device. Please contact the support structure for further assistance.The current microcode level for %1$s could not be determined."M" is the most recent level of microcode found on the source. It is later than the level of microcode currently installed on the device. "L" identifies levels of microcode that are later than the level of microcode currently installed on the device. Multiple later images are listed in descending order. "C" identifies the level of microcode currently installed on the device. "P" identifies levels of microcode that are previous to the level of microcode currently installed on the device. Multiple previous images are listed in the descending order.The current microcode for %1$s is %2$s. The microcode image currently installed on the device could not be found on the selected source. To install microcode, use the -f flag.An error was detected while unconfiguring %1$s. Unable to return the device to its original state. Run diagnostics on the device to isolate the problem.The previous level of microcode could not be found on the selected source.A later level of microcode could not be found on the selected source.The task indicates that there is no diskette drive present in the system. /etc/microcode is not available as microcode source in this boot mode. Either add a diskette drive to the system, or boot using disk as boot device and use /etc/microcode as the microcode source.***NOTICE***NOTICE***NOTICE*** The microcode installation occurs while the attached drives are available for use. It is recommended that this installation be scheduled during non-peak production periods. As with any microcode installation involving drives, a current backup should be available.No valid microcode file for %1$s was found. Microcode files must be located on the NIM server in usr/lib/microcode of the SPOT. Microcode files for this adapter have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.The Vital Product Data did not get updated. This will be updated the next time the system is rebooted.Invalid Source: %1$s The selected source is not present or is currently unavailable. Select a different source for the microcode download.