ISO8859-1$]P6?vu 5 o & 4 h [ r 7  Y - L z\Fp  Y =h / JJE1 wqfSN DISPLAY MICROCODE LEVEL %1$s %2$sINSTALL MICROCODE %1$s %2$sdiag [-c] -d -T disp_mcode -c No console mode. Run without user interaction. -d Run the task on the device specified. -T disp_mcode Display the microcode level.diag [-c] -d -T "download [-s {/etc/microcode|diskette}] [-l {latest|previous}] [-f]" -c No console mode. Run without user interaction. -d Run the task on the device specified. -T download Install microcode. -s /etc/microcode Microcode image is in /etc/microcode. Default. -s diskette Microcode image is on diskette. -l latest Install latest level of microcode. Default. -l previous Install previous level of microcode. -f Install microcode even if the current level is not on source.diag [-c] -d -T "download [-s {/etc/microcode|diskette|}] [-l {latest|previous}] [-f]" -c No console mode. Run without user interaction. -d Run the task on the resource specified. -T download Install microcode. -s /etc/microcode Microcode image is in /etc/microcode. Default. -s diskette Microcode image is on diskette. -s Microcode image is on identified source. For example fd0, cd0. -l latest Install latest level of microcode. Default. -l previous Install previous level of microcode. -f Install microcode even if the current level is not on source.Please run diagnostics on the adapter to ensure that it is functioning properly.Run diagnostics on the adapter to isolate the problem./etc/microcodedisketteHowever, an error was detected while unconfiguring the adapter. Unable to return the adapter to its original state. The source of the microcode image can either be on the disk in /etc/microcode or on a diskette. Select the source of the microcode image.Insert the microcode diskette in diskette drive %1$s.There is no diskette drive on the system. Please use /etc/microcode as the source for the microcode image file.Microcode installation is in progress.Installation of the microcode has completed successfully. The current microcode level for %1$s is %2$s. Installation of the microcode has not completed successfully. The current microcode level for %1$s is still %2$s. The current microcode level for %1$s is %2$s. Available levels to install are listed below. Select the microcode level to be installed. Use Help for explanations of "M", "L", "C" and "P" .%1$c %2$sHowever, ODM was not updated. Please do a rmdev followed by a mkdev on the adapter to get ODM updated. Until this is done, neither the lscfg command nor the Display Microcode diagnostic task will reflect the correct microcode information.A software error occurred. Contact the service support structure for further assistance.The current microcode level for %1$s is %2$s. *** NOTICE *** NOTICE *** NOTICE *** The microcode installation occurs while the adapter and any attached drives are available for use. It is recommended that this installation be scheduled during non-peak production periods. As with any microcode installation involving drives, a current backup should be available. Use Enter to continue the installation. Use F3 or F10 to cancel the installation. An error was detected while configuring %1$s. Run diagnostics on the adapter to isolate the problem. If no problem is found, retry the installation. If this error reoccurs, contact the service support structure for further assistance. The microcode image currently installed on the adapter could not be found on the selected source. Use Enter to continue the installation. Use F3 or F10 to cancel the installation.The adapter is already at the selected microcode level. Use Enter to continue the installation. Use F3 or F10 to cancel the installation.There was a problem accessing %1$s. Please make sure there is a microcode diskette in %2$s.Could not restore the image from %1$s. Please make sure there is a microcode diskette in backup format in %2$s.No valid microcode file for %1$s was found in /etc/microcode. Microcode files for this adapter have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.No valid microcode file for %1$s was found on the diskette in /etc/microcode. Microcode files for this adapter have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.There was a problem with the microcode file %1$s. Please make sure that the file is a valid microcode image and is not corrupted. A software error occurred. Contact the service support structure for further assistance. The current microcode level for %1$s could not be determined."M" is the most recent level of microcode found on the source. It is later than the level of microcode currently installed on the adapter. "L" identifies levels of microcode that are later than the level of microcode currently installed on the adapter. Multiple later images are listed in descending order. "C" identifies the level of microcode currently installed on the adapter. "P" identifies levels of microcode that are previous to the level of microcode currently installed on the adapter. Multiple previous images are listed in the descending order.To install from disk, microcode must be located in /etc/microcode. To install from diskette, the microcode must be in backup format with a path of /etc/microcode. Use Enter to continue.The current microcode level for %1$s is %2$s. The microcode image currently installed on the adapter could not be found on the selected source. To install microcode, use the -f flag.An error was detected while unconfiguring %1$s. Unable to return the adapter to its original state. Run diagnostics on the adapter to isolate the problem.The previous level of microcode could not be found on the selected source.A later level of microcode could not be found on the selected source.The task indicates that there is no diskette drive present in the system. /etc/microcode is not available as microcode source in this boot mode. Either add a diskette drive to the system, or boot using disk as boot device and use /etc/microcode as the microcode source.No valid microcode file for %1$s was found on the diskette in /etc/microcode. Ensure that the diskette is in backup format and that the microcode files have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.No valid microcode file for %1$s was found. Microcode files must be located on the NIM server in usr/lib/microcode of the SPOT. Microcode files for this adapter have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.No valid microcode file for %1$s was found in /etc/microcode. Microcode files for this adapter have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.No valid microcode file for %1$s was found on the diskette in /etc/microcode. Ensure that the diskette is in backup format and that the microcode files have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.No valid microcode file for %1$s was found. Microcode files must be located on the NIM server in usr/lib/microcode of the SPOT. Microcode files for this adapter have the naming convention %2$s.XXXXXX where XXXXXX is the level of the microcode.%1$s is not available on the system and can not be selected as a microcode source. No valid microcode file for %1$s was found on the optical media. Microcode files for this adapter have the naming convention %2$s.XXXXXXXX where XXXXXXXX is the level of the microcode.The system configuration indicates that there are client processes using this adapter. Microcode Download can not proceed under these circumstances.