ISO8859-1 P \jsx$ 9 Q uG  =3X%m~-G  )9J7j* '-/    wh ?F \ e ' y3kIUV'~RCSRfFS7'8^`y9%file systemoptical mediadiskettetapeISO 9660 file systemformatFailed to install microcode on %1$s. Installation of the microcode has completed successfully.Please run diagnostics on the resource to ensure that it is functioning properly.However, an error was detected while unconfiguring the resource. Unable to return the resource to its original state.However, ODM was not updated. Please run rmdev -l %1$s -R followed by cfgmgr -l %2$s to get ODM updated. Until this gets done, neither the lscfg command nor the Display Microcode diagnostic task will reflect the correct microcode information.Installation of the microcode has not completed successfully.The current microcode level for %1$s is still %2$s.A software error occurred. Contact the service support structure for further assistance.The resource %1$s is currently in use. Free the resource and attempt the installation of the microcode again.The current microcode level for %1$s is %2$s.The current microcode level for %1$s is %2$s. However the adapter is currently running at level %3$s The level %4$s will be used the next time the adapter is configured.FAILURE ! Installation of the microcode has NOT completed successfully.flashdriveconfigure deviceSelected sourceusb mass storageINSTALL MICROCODE %1$-16s %2$sInsert the media containing the microcode file in %1$s.Select the source of the microcode image. %1$s (%2$s format)Please stand by. Available levels to install are listed below. Select the microcode level to be installed. Use Help for explanations of "M", "L", "C" and "P".%1$c %2$s Microcode installation is in progress.An error was detected while configuring %1$s.Run diagnostics on %1$s to isolate the problem.If no problem is found, retry the microcode installation. If the problem reoccurs, contact the service support structure for further assistance. ***NOTICE***NOTICE***NOTICE***The microcode installation occurs while the selected device is available for use. It is recommended that this installation be scheduled during non-peak production periods.The microcode installation occurs while the selected adapter and any attached devices are available for use. It is recommended that this installation be scheduled during non-peak production periods.As with any microcode installation involving drives, a current backup of the system should be available.Use Enter to continue the installation. Use F3 to cancel installation.The selected source %1$s indicates that it is busy. Please make sure that it is not in use by another process. If it is in use, make it available before selecting it as the microcode source. Or select another source.There was a problem accessing %1$s. Please make sure that there is mountable media in %2$s.There was a problem accessing %1$s. Please make sure that microcode media in %2$s format is in %3$s.There was a problem accessing %1$s. Please make sure that there is a microcode media in %2$s that can be read using dosread utility.Could not access the microcode images from %1$s. Please make sure that the media is in %2$s format and is not corrupted.Could not restore the microcode images from %1$s. Please make sure that there is microcode media in %2$s format and it is not corrupted.Could not restore the microcode images from %1$s. Please make sure that the media can be read using the dosread utility and it is not corrupted.No valid microcode file for %1$s was found in %2$s.Microcode files for this resource have the naming convention %1$s where %2$s is the level of the microcode.The corresponding microcode file could not be found on the microcode source. To force installation of the microcode, use the -f flag."A microcode file for %1$s later than the current level of %2$s was not found on %3$s.A microcode file for %1$s previous to the current level of %2$s was not found on %3$s.There was a problem with the microcode file %1$s. Please make sure that the file is a valid microcode image and is not corrupted.This menu lists all the available sources for the microcode image. Note that different sources support different formats. Make sure that the microcode image file is in the supported format. If the server is booted from a NIM server, microcode must be located in the %1$s of the SPOT the client is booted from. Use Enter to continue.This menu lists all the available sources for the microcode image. Note that different sources support different formats. Make sure that the microcode image file is in the supported format. If the system is booted from a NIM server, microcode must be located in usr/lib/microcode of the SPOT the client is booted from.The microcode image currently installed on the resource could not be found on the selected source or in %1$s. The current image is not required for the installation. It is only a precaution in the event that there is a desire to reinstall it in the future.The microcode image currently installed on the %1$s could not be found on the selected source. The current image is not required for the installation. It is only a precaution in the event that there is a desire to reinstall it in the future.A software error occurred. The current level could not be determined. Contact the service support structure for further assistance.%1$s is not available on the system and can not be selected as a microcode source.The resource is already at the selected microcode level. Use Enter to continue the installation. Use F3 to cancel the installation.If the level of the microcode on the resource is known, it is identified on the first line of the menu. "M" is the most recent level of microcode found on the source. "L" identifies levels of microcode that are later than the level currently installed on the resource. If the current level is not known, all levels are considered later than the current level. Multiple later images are listed in descending order. "C" identifies the level of microcode currently installed on the resource. "P" identifies levels of microcode that are previous to the level of microcode currently installed on the resource. Multiple previous images are listed in descending order. Use Enter to continue.Please insert flashdrives containing microcode files and press Enter. Please insert USB Mass Storage devices containing microcode files and press Enter. Install Microcode Usage error for %1$s.Usage error. Use the following syntax when attempting to run this task from the command line:diag [-c] -d -T "download [-s ] [-l {latest|previous}] [-f]" -c No console mode. Run without user interaction. -d Run the task on the resource specified. -T download Install micrococde. -s Specify the source for the microcode. /etc/microcode or device name like fd0, cd0. The default is /etc/microcode. -l latest Install latest level of microcode. This is default. -l previous Install previous level of microcode. -f Install microcode even if the current level is not on source.diag [-c] -d -T disp_mcode -c No console mode. Run without user interaction. -d Run the task on the resource specified. -T disp_mcode Display the microcode level.DISPLAY MICROCODE LEVEL %1$-16s %2$s