ùISO8859-1Œ-©:×AcTT¸" 0 @ R h } —'§%Ïõ $>èR<;=x ¶ç » £ §Ÿ ª‘ J3Ü3[DR  ó#&7Jaw‰ (š &à ê Adapter configuration error.Error Log Analysis indicates adapter failure.Error Log Analysis indicates an Error Attention condition.Error Log Analysis indicates permanent adapter error is reported.Error Log Analysis indicates permanent adapter error is reported on the other port of this adapter.Error Log Analysis indicates that the microcode could not be loaded on the adapter.Configuration register test failedVPD test failedFlash test failedInterrupt test failedRegister test failedExternal link test failedDMA test failedInternal parallel path wrap test failedInternal serial path wrap test failedExternal wrap test failedEEH Error%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found. However, resource %4$s could not be restored to its initial defined state. If you do not want the resource to remain in the available state, run the following command from the command line: rmdev -l %5$s -R%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Analysis of the error log indicates a microcode problem. Ensure the microcode is the latest version available. If microcode is already the latest version and the problem persists, contact your local service support.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has detected multiple communication errors. Refer to the Storage Area Network (SAN) problem determination procedures for additional problem resolution.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has detected multiple communication errors. These errors can be caused by network configuration problems or too many initiators. Refer to the Storage Area Network (SAN) problem determination procedures for additional problem resolution.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has detected multiple communication errors. These errors can be caused by attached devices, a switch, or a SCSI-to-FC convertor. Refer to the Storage Area Network (SAN) problem determination procedures for additional problem resolution.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis does not indicate any problems. However, no tests could be run on the resource since it was in use. To perform tests, free the resource and run Advanced Diagnostics on the resource.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has analyzed the hardware errors that were logged against this adapter starting at %4$s on %5$s and ending at %6$s on %7$s. The number of errors analyzed: %8$d. The Diagnostic Application has determined that the adapter is functioning properly. No repair actions or additional problem determination procedures need to be performed at this time. Error Log Analysis will continue to monitor this adapter. YESNOThe remaining tests require a fibre connector wrap plug with one of the following Part Numbers: %1$s. Do you have this wrap plug and want to continue testing?* * * CAUTION * * * CAUTION * * * CAUTION * * * Looking into the fibre optic cable can damage your eyes. UNPLUG.........the fibre cable, if attached, from the connector on the fibre channel adapter. PLUG...........the wrap plug into the connector on the fibre channel adapter. Use a wrap plug with one of the following Part Numbers: %1$s.* * * CAUTION * * * CAUTION * * * CAUTION * * * Looking into the fibre optic cable can damage your eyes. UNPLUG.........the wrap plug from the connector on the fibre channel adapter. PLUG...........the fibre cable, if removed, into the connector on the fibre channel adapter.Closing the adapter may require up to %1$s minutes.* * * NOTICE * * * NOTICE * * * NOTICE * * * Wrap tests are not executed during loop mode.Module Information Expected Speed:..... %1$d Gbps Current Speed:...... %2$d Gbps Opening deviceRunning configuration register testRunning VPD testRunning Flash testRunning Interrupt testRunning Register testRunning Link testRunning DMA testRunning Internal parallel path wrap testRunning Internal serial path wrap testRunning External wrap testClosing device