ISO8859-1$TX[`ejo  P ] O[ \ anj>`fIOOFOO 6 ; L p  = !a"#,$ &Z$$0Y#4} ' - +4,    - 9 C a   3GVsYESNOV.24V.35V.36X.21When finished, press Enter.PCI 2-Port Multiprotocol AdapterTESTING PCI 2-PORT MULTIPROTOCOL ADAPTER %1$s IN LOCATION %2$s Please stand by.TESTING PORT %1$s OF PCI 2-PORT MULTIPROTOCOL ADAPTER %2$s IN LOCATION %3$s Please stand by.TESTING PCI 2-PORT MULTIPROTOCOL ADAPTER %1$s IN LOCATION %2$s IN ADVANCED MODETESTING PORT %1$s OF PCI 2-PORT MULTIPROTOCOL ADAPTER %2$s IN LOCATION %3$s IN ADVANCED MODETESTING PCI 2-PORT MULTIPROTOCOL ADAPTER %1$s IN LOCATION %2$s IN ADVANCED MODE Please stand by.TESTING PORT %1$s OF PCI 2-PORT MULTIPROTOCOL ADAPTER %2$s IN LOCATION %3$s IN ADVANCED MODE Please stand by.You will be given the opportunity to test both ports on the adapter. Do you want to test port 0? Make selection, then press Enter.Do you want to test port 1? Make selection, then press Enter.The following test uses a PCI 2-Port Multiprotocol Adapter port wrap plug (Part Number %1$s) to exercise all interfaces for this port. Do you have this wrap plug? Make selection, then press Enter.UNPLUG.........any attached cable from port %1$s of the adapter. PLUG...........the PCI 2-Port Multiprotocol Adapter port wrap plug (Part Number %2$s) into port %1$s of the adapter.Select the interface to be tested for this port. The cable and wrap plug listed below for the interface will be required during the test. Make selection, then press Enter.V.24 cable Part Number %1$s wrap plug Part Number %2$sV.35 cable Part Number %1$s wrap plug Part Number %2$sV.36 cable Part Number %1$s wrap plug Part Number %2$sX.21 cable Part Number %1$s wrap plug Part Number %2$sNoneUNPLUG.........the PCI 2-Port Multiprotocol Adapter port wrap plug from port %1$s of the adapter. PLUG...........the %2$s cable (Part Number %3$s) into port %1$s of the Adapter. UNPLUG.........the other end of the %2$s cable from any remote system. PLUG...........the %2$s wrap plug (Part Number %4$s) into the end of the %2$s cable.UNPLUG.........any attached cable from port %1$s of PCI 2-Port Multiprotocol Adapter. PLUG...........the %2$s cable (Part Number %3$s) into port %1$s of the Adapter. UNPLUG.........the other end of the %2$s cable from any remote system. PLUG...........the %2$s wrap plug (Part Number %4$s) into the end of the %2$s cable.Restore the cable configuration that existed for port %1$s prior to testing.Port 0 is already configured for wrap test during loop mode. Do not alter the port 0 wrap configuration while wrapping port 1.TESTING PCI 2-PORT MULTIPROTOCOL ADAPTER %1$s IN LOCATION %2$s IN LOOP MODE Testing multiple times. %3$s passes completed. %4$s errors logged. To stop the test, use 'Cancel.'TESTING PORT %1$s OF PCI 2-PORT MULTIPROTOCOL ADAPTER %2$s IN LOCATION %3$s IN LOOP MODE Testing multiple times. %4$s passes completed. %5$s errors logged. To stop the test, use 'Cancel.'You will be given the opportunity to test both ports on the adapter. Do you want to test port 0?Do you want to test port 1?The following test uses a PCI 2-Port Multiprotocol Adapter port wrap plug (Part Number %1$s) to exercise all interfaces for this port. Do you have this wrap plug?Select the interface to be tested for this port. The cable and wrap plug listed below for the interface will be required during the test.PCI 2-Port Multiprotocol Adapter CableSoftwareInternal Adapter Test Failed.External wrap test failed on port 0.External wrap test failed on port 1.Error Log Analysis Indicates A Hardware Problem.Error Log Analysis indicates that this device has failed to initialize due to EEH errors.Enhanced Error Handling failure opening the adapter.Enhanced Error Handling failure on bus.Enhanced Error Handling failure on Eads chip.Enhanced Error Handling failure on adapter.%1$06.6lx ADDITIONAL INFORMATION FOR (%2$s) IN LOCATION %3$s A device error log entry has been detected. The error log entry does not necessarily imply a failure of the adapter. Look at the error log entries for this device for more information.%1$06.6lx ADDITIONAL INFORMATION FOR (%2$s) IN LOCATION %3$s The diagnostic application failed to close the device. This indicates a system software error.Opening deviceConfiguration register testReset testRegister testSRAM memory testInterrupt testTiming testChip testTesting V24 protocol on port0Testing V24 protocol on port1Testing V35 protocol on port0Testing V35 protocol on port1Testing V36 protocol on port0Testing V36 protocol on port1Testing X21 protocol on port0Testing X21 protocol on port1Identifying adapterClosing deviceEnhanced Error Handling TestVerifying adapter response