ùISO8859-1|€uƒšù1”NÆqW‡ ß$ì#7S,o-œ -Ê ø  2 &Ov ~Ž¥ ·ÂÕêý    <  \  l€ m îˆ ðÍyeG½­†k òYESNOThe following test requires a wrap plug with a part number from the following list: %1$s Do you have this wrap plug?* * CAUTION * * CAUTION * * CAUTION * * CAUTION * * CAUTION Looking into the fibre optic cable can damage your eyes. UNPLUG.........the cable, if attached, from the connector on the ethernet adapter. PLUG...........the wrap plug into the ethernet adapter connector. Use a wrap plug with a part number from the following list: %1$s* * CAUTION * * CAUTION * * CAUTION * * CAUTION * * CAUTION Looking into the fibre optic cable can damage your eyes. UNPLUG.........the wrap plug from the connector on the ethernet adapter. PLUG...........the cable, if removed, into the connector on the ethernet adapter.Is the ethernet adapter under test connected to a functional ethernet network?Do you have a functional ethernet network that you would like to attach this adapter to and perform link testing?* * CAUTION * * CAUTION * * CAUTION * * CAUTION * * CAUTION Looking into the fibre optic cable can damage your eyes. PLUG...........the network cable, if not attached, into the connector on the ethernet adapter. ENSURE.........the other end of the network cable is connected to a functioning network.EEH failure.Configuration register test failure.VPD test failure.Flash test failure.Internal wrap test failure.External wrap test failure.External wrap with IP checksum test failure.External wrap with UDP checksum test failure.External wrap with TCP checksum test failure.Network link test failure.ELA detected hardware failure.ELA detected EEPROM failure.ELA transmission error count exceeded.NetworkOpening adapterPCI Configuration testVPD Checksum testFlash testInternal Wrap testNetwork Connect testExternal Wrap testExternal Wrap/IP Checksum testExternal Wrap/TCP Checksum testExternal Wrap/UDP Checksum testClosing adapter%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, the ethernet adapter diagnostics indicate that there may be a problem with the connection to the network. It is suggested that Advanced Diagnostic Testing with the wrap plug be performed on this adapter in order to better isolate the cause of this network interface problem.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, Error Log Analysis indicates that there may have recently been a network problem. If your ethernet adapter is connected to the network, and if you are experiencing problems with your network communications, check for a loose or defective cable or connection. If a switch or another system is directly attached to the ethernet adapter, verify that it is powered up, configured and functioning corectly.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis indicates that a failover operation has failed. Neither of the Ethernet ports has connectivity. Check for a loose or defective cable or connection to the Ethernet adapter. If a switch or another system is directly attached to the Ethernet adapter, verify it is powered up, configured, and functioning correctly.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis indicates that there recently has been a network problem. Although a failover attempt is successful, you may now have an Ethernet port that requires your attention. Check for a loose or defective cable or connection to the Ethernet adapter. If a switch or another system is directly attached to the Ethernet adapter, verify it is powered up, configured, and functioning correctly.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found. However, the resource was not tested because it has the following sibling ports configured: %4$s To test this resource, you can perform one of the following: 1) Unconfigure its other ports (%4$s) and run Diagnostics again. To unconfigure a port, run the following command from the command line: rmdev -Rl After running Diagnostics, run the following command: cfgmgr 2) Shut down the system and run in maintenance mode. 3) Run Diagnostics from the Diagnostic Standalone package. NOTE: No tests were run on the adapter because sibling fibre channel ports are in use. To perform tests, free the sibling fibre channel ports and run Advanced Diagnostics on the adapter.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, the ethernet adapter diagnostics indicate that there may be a problem with the connection to the network. It is suggested that Advanced Diagnostic Testing with the wrap plug be performed on this adapter in order to better isolate the cause of this network interface problem. %4$s%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, Error Log Analysis indicates that there may have recently been a network problem. If your ethernet adapter is connected to the network, and if you are experiencing problems with your network communications, check for a loose or defective cable or connection. If a switch or another system is directly attached to the ethernet adapter, verify that it is powered up, configured and functioning corectly. %4$s