ISO8859-1 :3m[n M S  *DXk~! , ?  O C I = ? Q [        2 E  `  {     B %% h1)hS + E7YESNOThe following test requires a fibre connector wrap plug with one of the following Part Numbers: %1$s. Do you have this wrap plug?* * * CAUTION * * * CAUTION * * * CAUTION * * * Looking into the fibre optic cable can damage your eyes. UNPLUG.........the fibre cable, if attached, from the connector on the fibre channel adapter. PLUG...........the wrap plug into the connector on the fibre channel adapter. Use a wrap plug with one of the following Part Numbers: %1$s.* * * CAUTION * * * CAUTION * * * CAUTION * * * Looking into the fibre optic cable can damage your eyes. UNPLUG.........the wrap plug from the connector on the fibre channel adapter. PLUG...........the fibre cable, if removed, into the connector on the fibre channel adapter.Closing the adapter may require a few minutes. Time depends on how many devices are attached to the adapter.* * * NOTICE * * * NOTICE * * * NOTICE * * * Wrap tests are not executed during loop mode.The following test requires a RJ-45 connector wrap plug with one of the following Part Numbers: %1$s. Do you have this wrap plug?UNPLUG.........the cable, if attached, from the connector on the adapter. PLUG...........the wrap plug into the connector on the adapter. Use a wrap plug with one of the following Part Numbers: %1$s.UNPLUG.........the wrap plug from the connector on the adapter. PLUG...........the cable, if removed, into the connector on the fibre channel adapter.An Adapter Register Test Failed.Local Memory Test Failed.Memory Test Failed.NVRAM Test Failed.Flash Test Failed.Internal Wrap Test Failed.External Wrap Test Failed.Direct Memory Access Test Failed.Enhanced Error Handling Failure Encountered.Error Log Analysis indicates that the adapter self-test failed.Error Log Analysis indicates that an NVRAM failure on the adapter has occurred.Error Log Analysis indicates that an error has occurred with the adapter.Error Log Analysis indicates that a fatal error has occurred.Error Log Analysis indicates that adapter errors have occurred.Error Log Analysis indicates than an unknown adapter hardware error has occurred.Opening deviceRunning register testRunning local memory size testRunning local memory testRunning memory testRunning NVRAM testRunning Flash testRunning internal wrap testRunning external wrap testRunning DMA testClosing device NOTE: No tests were run on the adapter because it was in use. To perform tests, free the adapter and run Advanced Diagnostics on it.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis indicates a possible problem with the adapter microcode. Make sure that the latest level of microcode is installed on the adapter. If the microcode is at the latest level and the problem persists, contact your service support structure. %4$s%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has detected a communication error. This error can be caused by an attached device or a switch. %4$s Refer to the Storage Area Network (SAN) problem determination procedures for additional problem resolution. %5$s The iSCSI name of the suspected device is: %1$s %1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has detected multiple communication errors. These errors can be caused by attached devices or a switch. Refer to the Storage Area Network (SAN) problem determination procedures for additional problem resolution. %4$s%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis has detected multiple link errors. These errors can be caused by loose or defective cables or the iSCSI TOE adapter. Check all cables and their connections. Run advanced diagnostics including wrap tests if prompted, to ensure the adapter link module is functioning properly. %4$s%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log analysis has detected multiple link errors. These errors can be caused by loose or defective cables. Check all cables and their connections. %4$s%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found. However, resource %4$s was not tested because the sibling resource %5$s was using shared resources common to both ports on a dual port adapter. To test this resource, you can do any one of the following: Free sibling resource %6$s and continue testing. Shut down the system and run in maintenance mode. Run Diagnostics from the Diagnostic Standalone Package. %7$s%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found. However, the sibling resource could not be restored back to its original state. The sibling resource needed - %4$s in location %5$s Please run rmdev -l %6$s -R followed by cfgmgr -l %7$s to restore the sibling resource. %8$sLocal RAM tests will be disabled because the sibling resource %1$s is using shared resources common to both ports on a dual port adapter. Use Enter to continue testing, F3 to cancel testing, or F10 to exit.Local RAM tests will be disabled because the sibling resource %1$s is using shared resources common to both ports on a dual port adapter.