ISO8859-1.  R ] P gF"!-3K86$  - G # f!# " # $ % @& _' ( 3) *+,- .#/-Ff ## # $3 X &m ('"))2(\,#"!3Rn%* ,!#1"#U#+y W-O# c" AYESNOThe adapter will not be completely tested unless it is connected to a functional network. Do you want to run the Loopback Test now? WARNING: for this test adapter must be connected to a functional infiniband network.PLUG........the network cable, if not attached, into the connector on the adapter. ENSURE......the other end of the network cable is connected to a functioning network.Configuration failureQueue Pair Create failureLoopback Test failureIB CableIB NetworkError Log Analysis indicates that this adapter has failed due to a internal error.Error Log Analysis indicates that this adapter has failed due to a failure with the uplink interface used to connect this device to the host processor.Error Log Analysis indicates that this adapter has failed due to a memory error.Error Log Analysis indicates that this adapter has failed due to a unrecoverable internal parity error.The adapter will not be completely tested unless it is connected to a functional network. Do you want to run the Loopback Test now? WARNING: for this test, the adapter must be connected to a functional network.Configuration register test failedEEH failure during testIO Register test failedChecksum verification test failedBIST test failedLink Detection test failedExternal Loopback test failedError Log Analysis indicates adapter hardware errorError Log Analysis indicates adapter configuration errorError Log Analysis indicates adapter EEH service errorInterrupt test failedTransceiver Verification test failedVPD Checksum test failed.Firmware Checksum test failed.Internal RDMA Loopback test failed.External RDMA Loopback test failed.The remaining tests require a wrap plug with one of the following Part Numbers: %1$s. Do you have this wrap plug and want to continue testing?UNPLUG.........the cables, if attached, from the connectors on the ethernet adapter. PLUG...........the wrap plug into the both connectors on the ethernet adapter. Use a wrap plug with one of the following Part Numbers: %1$s.UNPLUG.........the wrap plug from both connectors on the ethernet adapter. PLUG...........the cables, if removed, into the connectors on the ethernet adapter.UNPLUG.........the cable, if attached, from the connector on the ethernet adapter. PLUG...........the wrap plug into the connector on the ethernet adapter. Use a wrap plug with one of the following Part Numbers: %1$s.UNPLUG.........the wrap plug from the connector on the ethernet adapter. PLUG...........the cable, if removed, into the connector on the ethernet adapter.Optic Wrap Test FailedModule Information Transceiver FRU...... %1$s Transceiver SN....... %2$s Transceiver Vendor... %3$s Expected Speed....... %4$d Gbps Current Speed........ %5$d Gbps Transceiver Type..... %6$s UnknownEthernetFibre ChannelEthernet or Fibre ChannelRunning Configuration & Unconfiguration Test...Running Loopback Test...Loopback Test: 250 packets sentLoopback Test: 500 packets sentLoopback Test: 750 packets sentLoopback Test: 1000 packets sentLoopback Test: 250 packets receivedLoopback Test: 500 packets receivedLoopback Test: 750 packets receivedLoopback Test: 1000 packets receivedLoopback Test passedLoopback Test failed: internal failureLoopback Test failed: no packets in 10 sLoopback Test failed: corrupted packetsLoopback Test failed: lost packetsLoopback Test failed: lost+corrupted pcksLoopback Test failed to create Queue PairLoopback Test: creating 2 Queue Pairs...2 Queue Pairs have been created successfullyOpening deviceRunning Configuration register testRunning IO Register testRunning checksum verification testRunning BIST testRunning Internal Loopback testRunning Link detection testRunning External Loopback testClosing deviceRunning Interrupt testRunning Transceiver Verification testRunning VPD and Checksum verification testRunning Firmware Checksum Verificaction testRunning Internal RDMA Loopback testRunning External RDMA Loopback testRunning Firmware Checksum Verification test%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found. However, the resource was not tested because the device is not supported on a 32-bit kernel.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis indicates that there may have recently been a network problem. If your Infiniband adapter is connected to a network, and if you are experiencing problems with network communications, check for a loose or defective cable or connection. If a switch or another system is directly attached to the Infiniband adapter, verify that it is powered up, configured, and functioning correctly.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Error Log Analysis indicates that there may have recently been a network problem. If your adapter is connected to a network, and if you are experiencing problems with network communications, check for a loose or defective cable or connection. If a switch or another system is directly attached to the adapter, verify that it is powered up, configured, and functioning correctly.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, Error Log Analysis indicates that there may recently have been a network problem. If your adapter is connected to a network, and if you are experiencing problems with network communications, check for a loose connection or defective cable. If a switch or another system is directly attached to the adapter, verify that it is powered up, configured, and functioning correctly.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, Error Log Analysis indicates that there may be a problem with the connection to the network. Check for extensive network traffic. If this is not the cause, and if you are still experiencing problems, run advanced diagnostics.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found with this adapter. However, Error Log Analysis indicates that there may be a problem with the connection to the network. Check for extensive network traffic.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s No trouble was found. However, Error Log Analysis has detected that there are processes that have not released allocated resources. %2$s will remain busy until all allocated resources are freed. Below is a partial list of the processes responsible: PID - Process Name %4$s Use the following command to output error log information detailing these errors: errpt -a -N %2$s -J MLXENT_RDMA_RESOURC Contact your service support structure for further assistance.No trouble was found. However, the resource was not completely tested because the SR-IOV logical resource interface assigned to this partition indicated that the resource was not available for diagnostic mode. To completely test this resource: At the management console, enable diagnostic mode for the SR-IOV logical port assigned to this partition.No trouble was found. However, Error Log Analysis indicates the resource may not configure because the SR-IOV logical resource interface assigned to this partition has an access control list (ACL) violation. To view or edit the access control list for this resource or partition, please visit the manangement console.