ùISO8859-1#ÌÎЩÒ|/}À­n o p çq Y sw,z§¨©ª«¬­®ª¾ijk„lñåò?Ø z ! “"¸ ¤#ò ]%1 P" ‚" ¥ È à ü3  H & X #  + £ & Ï ) ö0 Q%n”³ÑêI6K‚‹©Æ0ä;WQE©,ï _!#|"* #1Ë$ý% 5 Tç` &Ho"¢¼Öó  TESTING SCSI DISK DRIVE %1$s IN LOCATION %2$s The test is attempting to start the disk drive motor. This will take approximately 1 minute to complete. Please stand by.TESTING SCSI DISK DRIVE %1$s IN LOCATION %2$s The disk drive indicates that it is write protected. The disk drive can be set in the write protect mode by the program or by a jumper. Should the disk drive be write protected at this time? TESTING SCSI DISK DRIVE %1$s IN LOCATION %2$s * * * WARNING! * * * Error Log Analysis has detected a number of non recoverable data errors. Please back up the SCSI Disk Drive %3$s and perform media maintenance on the disk drive. To continue, press Enter.YESNOMove cursor to selection, then press Enter. SCSI DISK DRIVE%1$6X TESTING SCSI DISK DRIVE %2$s IN LOCATION %3$s A number of attributes are found to be missing from the Data Base. Unexpected results may occur due to this problem.TESTING SCSI DISK DRIVE %1$s IN LOCATION %2$s The disk drive format is damaged. Use the Format Media Task to format the disk drive.CERTIFY MEDIA TASK The certify operation has detected excessive errors that are not recoverable. It is recommended that the data on the disk drive be backed up and that the media maintenance procedure be performed on the drive.TESTING SCSI DISK DRIVE %1$s IN LOCATION %2$s No trouble was found. Media verification can be done by running the CERTIFY MEDIA TASK. This will allow you to determine the number of recoverable and non-recoverable errors. The certify procedure may take up to %3$d minutes to complete. Do you want to certify the disk? The test is attempting to start the disk drive motor. This will take approximately 1 minute to complete. Please stand by.No trouble was found. Media verification can be done by running the CERTIFY MEDIA TASK. This will allow you to determine the number of recoverable and non-recoverable errors. The certify procedure may take up to %1$d minutes to complete. Do you want to certify the disk? * * * WARNING! * * * Error Log Analysis has detected a number of non recoverable data errors. Please back up the SCSI Disk Drive %1$s and perform media maintenance on the disk drive. TESTING SCSI DISK DRIVE %1$s IN LOCATION %2$s The block size of this disk drive is not compatible with the operating system. The disk drive needs to be formatted to the correct block size. Use the Format Media Task to format the disk drive.A medium error occurred that was not recoverable.The drive motor failed to restart.The drive electronics card failed.A bus failure occurred.Medium format is corrupted.Diagnostic test failed.A hardware error occurred that was not recoverable.Protocol error.A SCSI command timeout error occurred.A SCSI BUSY command error occurred.A SCSI RESERVATION CONFLICT error occurred.A SCSI CHECK CONDITION error occurred.Disk Drive has caused a software failure.Error log analysis indicates a hardware failure.The drive cannot be started.A Disk Drive hardware error occurred.A write protect error occured.857 MB Drive Electronics CardDrive head disk assemblyDrive Electronics CardError Log Analysis has detected error(s) that may require your attention.Use the Subsystem Service Guide to complete Diagnosis.SoftwareAdapter Configuration FailureDevice Configuration FailureThe certify operation failed.Error log analysis indicates a SCSI bus problem.SCSI bus problem: cables, terminators or other SCSI devicesError log analysis indicates problem reported by disk drive's self monitoring function.Unit attention condition has occurred on the Send Diagnostic command.SCSI cable, terminator or other SCSI devicesError Log Analysis indicates that the disk is operating at higher than recommended temperature.Error configuring or opening deviceError Log Analysis indicates a path error.Error log analysis indicates poor signal quality.SCSI cable/backplaneSSD CarrierADDITIONAL INFORMATION FOR %1$s IN LOCATION %2$s Error Log Analysis indicates a problem reported by disk drive %3$s in location %4$s. The drive's self montoring function has reported an error. BACKUP...the data in the disk. REPLACE...the disk. RESTORE...the data to the new disk. To continue, press Enter.ADDITIONAL INFORMATION FOR %1$s IN LOCATION %2$s The disk drive indicates that it is write protected. Check the drive's jumper settings to see if the drive is set to write protected. If it is not, the drive may be in a degraded read-only mode and should be replaced.ADDITIONAL INFORMATION FOR %1$s IN LOCATION %2$s Error Log Analysis indicates that the disk drive is operating at a higher than recommended temperature. The latest error was reported at %3$s 1. Verify that the room operating temperature is within the system operating environment. 2. There is unrestricted air flow around the system. 3. All system covers are closed. 4. There are no fan failures. Contact your service representative if the problem cannot be identified or corrected.Getting self-configuration informationReserving driveReadying drive for further testingGetting drive informationSetting drive informationRunning internal diagnosticsReleasing drivePerforming test on driveEstimating time to certify drive