ISO8859-1:H*H&f : 6 $+ P k%0/& %0V(j*"A@[/@6 7DD| =!1" 1#AR$F%I&D %'O j(Q ); *@ H+= ,7 -; .2 ;/2 n0D 1% 2% 3; 24Z n5J 6 75 /8W e9 :G ;:<4Y=[>"?( @\6A@B%CD` E/nF2G*H).&U#iKLoop mode testing will consist of error log analysis only.Adapter configuration error.Permanent controller failure.Controller failure.Temporary controller failure.Temporary controller failure.Storage subsystem configuration error.Temporary device bus error.Device problem.Cache data associated with attached disks cannot be found.Cache data belongs to disks other than those attached.Controller timed out a disk command.Temporary disk data error.Disk media format bad.PCI bus error detected by controller.Addressed device failed to respond to selection.Controller detected device bus interface error.Controller timed out a device command.PCI bus error detected by controller.Controller failure.Disk returned wrong response to adapter.Device bus interface error.Out of alternate sectors for disk storage.Temporary device bus error.Device detected recoverable error.RAID controller resources not available due to previous problems.Controller detected device error during configuration discovery.Disk has been modified after last known status.Controller detected device error during internal media recovery.Incorrect disk configuration change has been detected.Cache data exists for one or more missing/failed disks.Controller does not support function expected for one or more disks.Required cache data can not be located for one or more disks.Cache data exists for one or more modified disks.Disk requires Format before use.Two or more disks are missing from a RAID-5 or RAID 6 Disk Array.One or more Disk Array members are not at required physical locations.Physical location of Disk Array members conflict with another Disk Array.Incompatible disk installed at degraded disk location in Disk Array.Previously degraded disk in Disk Array not found at required physical location.Disk Array is or would become degraded and parity data is out of synchronization.Maximum number of functional Disk Arrays has been exceeded.Maximum number of functional Disk Array disks has been exceeded.One or more disk pairs are missing from a RAID-10 Disk Array.One or more disks are missing from a RAID-0 Disk Array.Maximum number of functional Disk Arrays has been exceeded.Automatic reconstruction initiated for Disk Array.Disk Array is degraded due to missing/failed disk.Background Disk Array parity checking detected and corrected errors.Impending Cache Battery Pack failure.Permanent Cache Battery Pack failure.Multiple controllers connected in an invalid configuration.Multiple controllers not capable of similar functions or controlling same set of devices.Incomplete multipath connection between controller and remote controller.Missing remote controller.Disk Array is degraded due to missing or failed disk.Background Disk Array parity checking detected and corrected errors on specified disk.Device bus fabric error.Configuration error, incorrect connection between cascaded enclosures.Configuration error, connections exceed IOA design limits.Configuration error, incorrect multipath connection.Configuration error, incorrect multipath connection between enclosure and device detected.Temporary device bus fabric error.Unsupported enclosure function detected.Configuration error, incomplete multipath connection between enclosure and device detected.Attached enclosure does not support required multipath function.Multipath redundancy level got worse.Cache Battery PackConfiguration error, incomplete multipath connection between controller and enclosure detected.A permanent Cache Battery Pack failure occured.Disk Array is degraded due to missing/failed disk.Controller device bus configuration error.Out of alternate disk storage for storage%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s An adapter configuration error has been detected. This may indicate an invalid configuration. Ensure there are not too many devices attached. Try disconnecting and reconnecting any attached cables. Check and verify correct SCSI configuration.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Analysis of the error log indicates a microcode problem. Ensure the microcode is the latest version available. If microcode is already the latest version and the problem presists, contact your local service support.%1$06.6lx ADDITIONAL INFOR0MATION FOR %2$s IN LOCATION %3$s No trouble was found. However, resource %4$s could not be restored to its initial defined state. If you do not want the device to remain in the available state, run the following command from the command line: rmdev -l %5$s -Rd%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s An adapter configuration error has been detected for bus number %4$d, id %5$d. This may indicate an invalid configuration. Ensure there are not too many devices attached. Try disconnecting and reconnecting any attached cables. Check and verify correct SCSI configuration.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s An adapter configuration error has been detected. This may indicate an invalid configuration. Check and verify correct controller configuration.%1$06.6lx ADDITIONAL INFORMATION FOR %2$s IN LOCATION %3$s Analysis of the error log indicates a microcode problem. Download the latest microcode available to the controller. If the problem presists, contact your local service support.